A Course in Electrical Machine Design /
A.K. Sawhney, A. Chakrabarti
- 6th edition
- Nai Srak : Dhanpat Rai & Co.Ltd., c2006.
- xxiv, 2334 p. : ill. ; 24 cm.
CONTENTS
Chapter 1 : Fundamental Aspects of electrical Machine design 1.1 Design of Machines 1.2 Design Factors 1.3 Limitations in Design 1.4 Modern trends in design of electrical machines etc.
Chapter 2: Electrical Engineering Materials 2.1 Electrical Conducting Materials 2.2 High Conductivity Materials 2.3 Materials of high Resistivity 2.4 Electrical Carbon Materials etc.
Chapter 3: Principles of Magnetic Circuit Design 3.1 Fundamentals of Magnetic Circuits 3.2 Magnetic Curves 3.3 Magnetic leakage 3.4 Calculation of Total mmf in a Magnetic Circuit etc.
Chapter 4: Thermal Design Aspect of electrical Machines 4.1 Modes of heat Dissipation 4.2 Newton's Law of cooling 4.3 Ambient Temperature 4.4 Internal temperatures (Hot Spot Temperatures) etc.
Chapter 5 : Design Transformers PART A : CONSTRUCTIONAL DETAILS 5.1 Introduction 5.2 Classification of transformers 5.3 Single and three phase transformers 5.4 Three Phase Transformer Connections etc.
Chapter 6 : General concepts and constraints in design of rotating machines 6.1 Relation between relating and dimensions of rotating machines 6.2 Variation of Output and losses with linear dimensions 6.3 Separation of D and L 5.15 6.4 Standard Frames etc.
Chapter 7 : Armature windings 7.1 Introduction 7.2 Single layer and two layer windings 7.3 Closed and open windings 7.4 Coils and Coil sides etc.
Chapter 8: Aspects of design of mechanical parts 8.1 Design of Shaft 8.2 Bearings 8.3 Shaft Couplings 8.4 Frames for D.C. Machines etc.
Chapter 9: D.C. Machines 9.1 Introduction and Applications 9.2 Classification 9.3 Constructional Details 9.4 Stator etc.
Chapter 10: Three phase Induction motors 10.1 Introduction 10.2 Stator 10.3 Stator frames 10.4 Rotor etc.
Chapter 11 : Design of Synchronous Machines 11.1 Types of construction 11.2 Type of synchronous machines 11.3 Prime movers for Synchronous generators 11.4 Run-away Speed etc
Chapter 12: Design of Single phase Induction Motors 12.1 Introduction 12.2 Types of Motors 12.3 Construction 12.4 Output equation etc.
Chapter 13 : Design of Permanent Magnet (PM) DC Motors 13.1 Introduction 13.2 Design preliminaries 13.3 Design steps 13.4 Supplementary Design Considerations etc.
Chapter 14: Design of Small Electrical Machines 14.1 Introduction 14.2 Design of Small DC Motors 14.3 Design of Small Universal Commutator motors 14.4 Design of a small reluctance motor etc.
Chapter 15 : Design of Electromagnets 15.1 Introduction 15.2 Types of Electromagnets 15.3 Construction of electromagnets 15.4 Index Number of electromagnets etc.
Chapter 16 : Design of heating elements, Inductors and welding Transformers 16.Heating elements 16.2 Design of round wire elements 16.3 Design of Ribbon elements 16.4 Design of power induction etc.
Chapter 17 : Design of Current Transformers (CT) AND Permanent Magnets (PM) 17.1 Introduction 17.2 Errors 17.3 Construction 17.4 Design principles etc.
Chapter 18: Design starter and field Regulators 18.1 Motor Starters 18.2 Calculation of resistance steps 18.3 Design of field Regulators for DC machines etc.
Chapter 19: Basic Aspects of Design of power electronic Converter transformers 19.1 Introduction 19.2 Transformer Utilization factor 19.3 Power rating and types of connection of converter transformers 19.4 Design of Single phase Converter Transformer etc.
Chapter 20: Asspects of design of induction motor in variable frequency inverter circuits 20.1 Introduction 20.2 Speed-torque curves 20.3 Aspect of variable-speed drives 20.4 Discussion about parameters in design as affected by variable frequency operation etc.
Chapter 21 : Aspects of Design of Control Machines 21.1 Aspect of design calculation for small DC Servomotor (Reversible speed Drive) 21.2 Aspect of design a selsyn 21.3 Design Calculation
Chapter 22 Computer application in electrical Machine design 22.1 Introduction 22.2 Advantages of Digital Computers 22.3 Computer Aided Design-Different approaches 22.4 Computer Aided Design of transformer etc.
Chapter 23: Standard Specifications 23.1 Indian specifications for Copper conductors used in Electrical Machines and apparatus 23.2 British standard Specifications 23.3 General 23.1 23.4 Outdoor type Distribution transformers IS;1180-1966 23.11 etc.